Can you make my F1 car hit 220+ ?

Citation10 · 16 January 08, 01:53

Hoping someone can tweak my can for awsome handling but insane speeds .

Thanks all

file is attached .

LordRa9826 · 16 January 08, 02:01

It's easy to do that.Open the .hdc file,lower the BodyDragBase for higher speeds,lower the Mass and the CGHeight for handling.

Citation10 · 16 January 08, 02:33

Thanks for the reply , Do I need to lower them by the hundreds or just a lille here and there .

Smuckers · 16 January 08, 03:33

// Zytek Engineering ZA1348 3,4L V8, max. Torque 442 nm
//
RPMTorque=( 0, -35.0, -36.0)
RPMTorque=( 250, -36.3, -20.0)
RPMTorque=( 500, -37.7, 119.0)
RPMTorque=( 750, -38.9, 196.0)
RPMTorque=( 1000, -39.2, 232.0)
RPMTorque=( 1250, -39.9, 274.0)
RPMTorque=( 1500, -40.4, 298.0)
RPMTorque=( 1750, -41.1, 321.0)
RPMTorque=( 2000, -41.9, 332.0)
RPMTorque=( 2250, -42.1, 352.0)
RPMTorque=( 2500, -42.8, 365.0)
RPMTorque=( 2750, -43.7, 381.0)
RPMTorque=( 3000, -44.6, 394.0)
RPMTorque=( 3250, -45.4, 406.0)
RPMTorque=( 3500, -46.7, 414.0)
RPMTorque=( 3750, -47.5, 423.0)
RPMTorque=( 4000, -48.3, 434.0)
RPMTorque=( 4250, -49.6, 445.2)
RPMTorque=( 4500, -50.9, 454.4)
RPMTorque=( 4750, -52.0, 465.3)
RPMTorque=( 5000, -54.1, 474.1)
RPMTorque=( 5250, -55.3, 481.6)
RPMTorque=( 5500, -56.6, 491.5)
RPMTorque=( 5750, -58.4, 502.1)
RPMTorque=( 6000, -60.5, 508.6)
RPMTorque=( 6250, -62.8, 515.8)
RPMTorque=( 6500, -64.7, 522.3)
RPMTorque=( 6750, -67.4, 528.5)
RPMTorque=( 7000, -70.2, 534.8)
RPMTorque=( 7250, -73.0, 538.9)
RPMTorque=( 7500, -74.2, 540.6)
RPMTorque=( 7750, -76.3, 542.0)
RPMTorque=( 8000, -78.2, 545.0)
RPMTorque=( 8250, -80.2, 540.9)
RPMTorque=( 8500, -81.4, 535.2)
RPMTorque=( 8750, -83.2, 525.0)
RPMTorque=( 9000, -85.0, 515.0)
RPMTorque=( 9250, -86.5, 500.0)
RPMTorque=( 9500, -87.9, 485.0)
RPMTorque=( 9750, -89.5, 430.0)
RPMTorque=( 10000, -91.7, 419.0)
RPMTorque=( 10250, -93.7, 397.0)
RPMTorque=( 10500, -97.0, 348.0)
RPMTorque=( 10750, -100.5, -6.0)
RPMTorque=( 11000, -101, -46.0)
FuelConsumption=6.305e-005 // affected by throttle position and engine speed
FuelEstimate=1.000 // fudge factor for differences between vehicle types (used for lap estimates and AI pit scheduling)0.997
EngineInertia=0.075 // rotational inertia of engine components
IdleThrottle=1.0 // throttle multiplier to help maintain idle speed
IdleRPMLogic=(1800.0, 2000.0) // attempt to maintain idle speed between these RPMs
LaunchEfficiency=0.000 // efficiency (0.0-1.0) of launch control, or 0.0 if N/A
LaunchRPMLogic=(6500.0, 8500.0) // holds RPM in this range before launch (used for AI even if launch control is N/A!)
RevLimitRange=(8200.0, 100.0, 8)
RevLimitSetting=3
RevLimitLogic=150.0 // RPM range around current setting where rev limiter operates
RevLimitAvailable=1 // whether to use a rev limit (if 0, you still must have a "rev limit", just make it 40000 or so, and make sure to change [CONTROLS]->UpshiftAlgorithm to fix shifting points)
EngineMapRange=(0, 1, 5) // 0 = most driveable, max = most power (low gears only) (unimplemented)
EngineMapSetting=1
EngineBrakingMapRange=(0.0, 0.000155, 5) // input throttle is ranged from minimum to 100%, with the minimum = setting * step * RPM,
EngineBrakingMapSetting=2 // the default is 1 * 0.000133 * 15000 RPM = 2% applied throttle at zero input throttle
OptimumOilTemp=105.0 // degrees Celsius at which engine operates optimally
CombustionHeat=30.0 // degrees Celsius added per liter of fuel burned
EngineSpeedHeat=7.800e-004 // heat added linearly with engine speed
OilMinimumCooling=9.150e-004 // heat dissipated without radiator
OilWaterHeatTransfer=(5.550e-003,9.050e-005) // heat transfer from oil to water (base, w/ engine speed)
WaterMinimumCooling=3.650e-003 // heat dissipated without radiator 3.900e-003
RadiatorCooling=(2.95e-004, 1.065e-004) // cooling rate with velocity (base, per setting)(3.00e-004, 1.060e-004)
LifetimeEngineRPM=(8850.0,360.0) // (base engine speed for lifetime, range where lifetime is halved)
LifetimeOilTemp=(130.0,2.90) // (base oil temp for lifetime, range where lifetime is halved)
LifetimeAvg=15850 // average lifetime in seconds
LifetimeVar=3800 // lifetime random variance
EngineEmission=(0.0, 0.50, 0.0) // where flames and smoke are emitted (relative to ref frame at rear axle)
EngineSound=(0.0, 0.50, 0.0) // where engine sound is played (relative to ref frame at rear axle)
SpeedLimiter=1 // whether vehicle has a pitlane speed limiter
OnboardStarter=1 // whether vehicle restarts when stalled
StarterTiming=(1.4, 0.4, 1.9) // average and variable cranking time, then time to blend with starting sound

Citation10 · 17 January 08, 00:39

I made some changed to the HDC file and I cant even drive the car now , its out of control ... would anyone mind tweaking it for me ?

Citation10 · 17 January 08, 01:55

Quote:

Originally Posted by Smuckers

// Zytek Engineering ZA1348 3,4L V8, max. Torque 442 nm
//
RPMTorque=( 0, -35.0, -36.0)
RPMTorque=( 250, -36.3, -20.0)
RPMTorque=( 500, -37.7, 119.0)
RPMTorque=( 750, -38.9, 196.0)
RPMTorque=( 1000, -39.2, 232.0)
RPMTorque=( 1250, -39.9, 274.0)
RPMTorque=( 1500, -40.4, 298.0)
RPMTorque=( 1750, -41.1, 321.0)
RPMTorque=( 2000, -41.9, 332.0)
RPMTorque=( 2250, -42.1, 352.0)
RPMTorque=( 2500, -42.8, 365.0)
RPMTorque=( 2750, -43.7, 381.0)
RPMTorque=( 3000, -44.6, 394.0)
RPMTorque=( 3250, -45.4, 406.0)
RPMTorque=( 3500, -46.7, 414.0)
RPMTorque=( 3750, -47.5, 423.0)
RPMTorque=( 4000, -48.3, 434.0)
RPMTorque=( 4250, -49.6, 445.2)
RPMTorque=( 4500, -50.9, 454.4)
RPMTorque=( 4750, -52.0, 465.3)
RPMTorque=( 5000, -54.1, 474.1)
RPMTorque=( 5250, -55.3, 481.6)
RPMTorque=( 5500, -56.6, 491.5)
RPMTorque=( 5750, -58.4, 502.1)
RPMTorque=( 6000, -60.5, 508.6)
RPMTorque=( 6250, -62.8, 515.8)
RPMTorque=( 6500, -64.7, 522.3)
RPMTorque=( 6750, -67.4, 528.5)
RPMTorque=( 7000, -70.2, 534.8)
RPMTorque=( 7250, -73.0, 538.9)
RPMTorque=( 7500, -74.2, 540.6)
RPMTorque=( 7750, -76.3, 542.0)
RPMTorque=( 8000, -78.2, 545.0)
RPMTorque=( 8250, -80.2, 540.9)
RPMTorque=( 8500, -81.4, 535.2)
RPMTorque=( 8750, -83.2, 525.0)
RPMTorque=( 9000, -85.0, 515.0)
RPMTorque=( 9250, -86.5, 500.0)
RPMTorque=( 9500, -87.9, 485.0)
RPMTorque=( 9750, -89.5, 430.0)
RPMTorque=( 10000, -91.7, 419.0)
RPMTorque=( 10250, -93.7, 397.0)
RPMTorque=( 10500, -97.0, 348.0)
RPMTorque=( 10750, -100.5, -6.0)
RPMTorque=( 11000, -101, -46.0)
FuelConsumption=6.305e-005 // affected by throttle position and engine speed
FuelEstimate=1.000 // fudge factor for differences between vehicle types (used for lap estimates and AI pit scheduling)0.997
EngineInertia=0.075 // rotational inertia of engine components
IdleThrottle=1.0 // throttle multiplier to help maintain idle speed
IdleRPMLogic=(1800.0, 2000.0) // attempt to maintain idle speed between these RPMs
LaunchEfficiency=0.000 // efficiency (0.0-1.0) of launch control, or 0.0 if N/A
LaunchRPMLogic=(6500.0, 8500.0) // holds RPM in this range before launch (used for AI even if launch control is N/A!)
RevLimitRange=(8200.0, 100.0, 8)
RevLimitSetting=3
RevLimitLogic=150.0 // RPM range around current setting where rev limiter operates
RevLimitAvailable=1 // whether to use a rev limit (if 0, you still must have a "rev limit", just make it 40000 or so, and make sure to change [CONTROLS]->UpshiftAlgorithm to fix shifting points)
EngineMapRange=(0, 1, 5) // 0 = most driveable, max = most power (low gears only) (unimplemented)
EngineMapSetting=1
EngineBrakingMapRange=(0.0, 0.000155, 5) // input throttle is ranged from minimum to 100%, with the minimum = setting * step * RPM,
EngineBrakingMapSetting=2 // the default is 1 * 0.000133 * 15000 RPM = 2% applied throttle at zero input throttle
OptimumOilTemp=105.0 // degrees Celsius at which engine operates optimally
CombustionHeat=30.0 // degrees Celsius added per liter of fuel burned
EngineSpeedHeat=7.800e-004 // heat added linearly with engine speed
OilMinimumCooling=9.150e-004 // heat dissipated without radiator
OilWaterHeatTransfer=(5.550e-003,9.050e-005) // heat transfer from oil to water (base, w/ engine speed)
WaterMinimumCooling=3.650e-003 // heat dissipated without radiator 3.900e-003
RadiatorCooling=(2.95e-004, 1.065e-004) // cooling rate with velocity (base, per setting)(3.00e-004, 1.060e-004)
LifetimeEngineRPM=(8850.0,360.0) // (base engine speed for lifetime, range where lifetime is halved)
LifetimeOilTemp=(130.0,2.90) // (base oil temp for lifetime, range where lifetime is halved)
LifetimeAvg=15850 // average lifetime in seconds
LifetimeVar=3800 // lifetime random variance
EngineEmission=(0.0, 0.50, 0.0) // where flames and smoke are emitted (relative to ref frame at rear axle)
EngineSound=(0.0, 0.50, 0.0) // where engine sound is played (relative to ref frame at rear axle)
SpeedLimiter=1 // whether vehicle has a pitlane speed limiter
OnboardStarter=1 // whether vehicle restarts when stalled
StarterTiming=(1.4, 0.4, 1.9) // average and variable cranking time, then time to blend with starting sound

181 MPH was top speed of that .

Smuckers · 18 January 08, 02:15

Quote:

Originally Posted by Smuckers

// Zytek Engineering ZA1348 3,4L V8, max. Torque 442 nm
//
RPMTorque=( 0, -35.0, -36.0)
RPMTorque=( 250, -36.3, -20.0)
RPMTorque=( 500, -37.7, 1119.0)
RPMTorque=( 750, -38.9, 1196.0)
RPMTorque=( 1000, -39.2, 1232.0)
RPMTorque=( 1250, -39.9, 1274.0)
RPMTorque=( 1500, -40.4, 1298.0)
RPMTorque=( 1750, -41.1, 1321.0)
RPMTorque=( 2000, -41.9, 1332.0)
RPMTorque=( 2250, -42.1, 1352.0)
RPMTorque=( 2500, -42.8, 1365.0)
RPMTorque=( 2750, -43.7, 1381.0)
RPMTorque=( 3000, -44.6, 1394.0)
RPMTorque=( 3250, -45.4, 1406.0)
RPMTorque=( 3500, -46.7, 1414.0)
RPMTorque=( 3750, -47.5, 1423.0)
RPMTorque=( 4000, -48.3, 1434.0)
RPMTorque=( 4250, -49.6, 1445.2)
RPMTorque=( 4500, -50.9, 1454.4)
RPMTorque=( 4750, -52.0, 1465.3)
RPMTorque=( 5000, -54.1, 1474.1)
RPMTorque=( 5250, -55.3, 1481.6)
RPMTorque=( 5500, -56.6, 1491.5)
RPMTorque=( 5750, -58.4, 1502.1)
RPMTorque=( 6000, -60.5, 1508.6)
RPMTorque=( 6250, -62.8, 1515.8)
RPMTorque=( 6500, -64.7, 1522.3)
RPMTorque=( 6750, -67.4, 1528.5)
RPMTorque=( 7000, -70.2, 1534.8)
RPMTorque=( 7250, -73.0, 1538.9)
RPMTorque=( 7500, -74.2, 1540.6)
RPMTorque=( 7750, -76.3, 1542.0)
RPMTorque=( 8000, -78.2, 1545.0)
RPMTorque=( 8250, -80.2, 1540.9)
RPMTorque=( 8500, -81.4, 1535.2)
RPMTorque=( 8750, -83.2, 1525.0)
RPMTorque=( 9000, -85.0, 1515.0)
RPMTorque=( 9250, -86.5, 1500.0)
RPMTorque=( 9500, -87.9, 1485.0)
RPMTorque=( 9750, -89.5, 1430.0)
RPMTorque=( 10000, -91.7, 1419.0)
RPMTorque=( 10250, -93.7, 1397.0)
RPMTorque=( 10500, -97.0, 1348.0)
RPMTorque=( 10750, -100.5, 1000.0)
RPMTorque=( 11000, -101, -46.0)
FuelConsumption=6.305e-005 // affected by throttle position and engine speed
FuelEstimate=1.000 // fudge factor for differences between vehicle types (used for lap estimates and AI pit scheduling)0.997
EngineInertia=0.075 // rotational inertia of engine components
IdleThrottle=1.0 // throttle multiplier to help maintain idle speed
IdleRPMLogic=(1800.0, 2000.0) // attempt to maintain idle speed between these RPMs
LaunchEfficiency=0.000 // efficiency (0.0-1.0) of launch control, or 0.0 if N/A
LaunchRPMLogic=(6500.0, 8500.0) // holds RPM in this range before launch (used for AI even if launch control is N/A!)
RevLimitRange=(8200.0, 100.0, 8)
RevLimitSetting=3
RevLimitLogic=150.0 // RPM range around current setting where rev limiter operates
RevLimitAvailable=1 // whether to use a rev limit (if 0, you still must have a "rev limit", just make it 40000 or so, and make sure to change [CONTROLS]->UpshiftAlgorithm to fix shifting points)
EngineMapRange=(0, 1, 5) // 0 = most driveable, max = most power (low gears only) (unimplemented)
EngineMapSetting=1
EngineBrakingMapRange=(0.0, 0.000155, 5) // input throttle is ranged from minimum to 100%, with the minimum = setting * step * RPM,
EngineBrakingMapSetting=2 // the default is 1 * 0.000133 * 15000 RPM = 2% applied throttle at zero input throttle
OptimumOilTemp=105.0 // degrees Celsius at which engine operates optimally
CombustionHeat=30.0 // degrees Celsius added per liter of fuel burned
EngineSpeedHeat=7.800e-004 // heat added linearly with engine speed
OilMinimumCooling=9.150e-004 // heat dissipated without radiator
OilWaterHeatTransfer=(5.550e-003,9.050e-005) // heat transfer from oil to water (base, w/ engine speed)
WaterMinimumCooling=3.650e-003 // heat dissipated without radiator 3.900e-003
RadiatorCooling=(2.95e-004, 1.065e-004) // cooling rate with velocity (base, per setting)(3.00e-004, 1.060e-004)
LifetimeEngineRPM=(8850.0,360.0) // (base engine speed for lifetime, range where lifetime is halved)
LifetimeOilTemp=(130.0,2.90) // (base oil temp for lifetime, range where lifetime is halved)
LifetimeAvg=15850 // average lifetime in seconds
LifetimeVar=3800 // lifetime random variance
EngineEmission=(0.0, 0.50, 0.0) // where flames and smoke are emitted (relative to ref frame at rear axle)
EngineSound=(0.0, 0.50, 0.0) // where engine sound is played (relative to ref frame at rear axle)
SpeedLimiter=1 // whether vehicle has a pitlane speed limiter
OnboardStarter=1 // whether vehicle restarts when stalled
StarterTiming=(1.4, 0.4, 1.9) // average and variable cranking time, then time to blend with starting sound

:roflmao:

Smuckers · 18 January 08, 02:23

RPMTorque=( 0.0, -32.3, -32.3)
RPMTorque=( 500.0, -32.1, -20.0)
RPMTorque=( 1000.0, -33.4, 3.0)
RPMTorque=( 1500.0, -35.2, 29.8)
RPMTorque=( 2000.0, -37.2, 59.5)
RPMTorque=( 2500.0, -39.1, 84.3)
RPMTorque=( 3000.0, -40.9, 137.2)
RPMTorque=( 3500.0, -42.8, 144.1)
RPMTorque=( 4000.0, -44.7, 157.9)
RPMTorque=( 4500.0, -46.6, 199.2)
RPMTorque=( 5000.0, -48.6, 240.6)
RPMTorque=( 5500.0, -50.7, 268.2)
RPMTorque=( 6000.0, -52.8, 309.5)
RPMTorque=( 6500.0, -55.0, 364.3)
RPMTorque=( 7000.0, -57.2, 385.3)
RPMTorque=( 7500.0, -59.4, 412.9)
RPMTorque=( 8000.0, -61.7, 433.6)
RPMTorque=( 8500.0, -63.9, 474.9)
RPMTorque=( 9000.0, -66.2, 509.4)
RPMTorque=( 9500.0, -68.5, 537.0)
RPMTorque=( 10000.0, -70.9, 557.6)
RPMTorque=( 10500.0, -73.4, 571.4)
RPMTorque=( 11000.0, -76.0, 599.0)
RPMTorque=( 11500.0, -78.9, 619.7)
RPMTorque=( 12000.0, -82.0, 633.5)
RPMTorque=( 12500.0, -85.4, 654.1)
RPMTorque=( 13000.0, -89.3, 681.7)
RPMTorque=( 13500.0, -93.6, 695.5)
RPMTorque=( 14000.0, -98.3, 702.4)
RPMTorque=( 14500.0, -103.4, 723.1)
RPMTorque=( 15000.0, -109.1, 736.8)
RPMTorque=( 15500.0, -114.9, 757.5)
RPMTorque=( 16000.0, -120.9, 764.4)
RPMTorque=( 16500.0, -127.0, 778.2)
RPMTorque=( 17000.0, -133.3, 785.1)
RPMTorque=( 17500.0, -139.6, 805.8)
RPMTorque=( 18000.0, -146.0, 819.5)
RPMTorque=( 18500.0, -155.4, 826.4)
RPMTorque=( 19000.0, -155.4, 833.3)
RPMTorque=( 19500.0, -161.7, 826.4)
RPMTorque=( 20000.0, -174.2, 840.2)
RPMTorque=( 20500.0, -180.5, 840.2)
RPMTorque=( 21000.0, -193.0, 847.1)
RPMTorque=( 21500.0, -193.0, 835.8)
RPMTorque=( 22000.0, -193.0, 835.8)
RPMTorque=( 22500.0, -193.0, 835.8)
RPMTorque=( 23000.0, -193.0, 835.8)
RPMTorque=( 23500.0, -193.0, 835.8)
RPMTorque=( 24000.0, -193.0, 835.8)
RPMTorque=( 24500.0, -193.0, 848.4)
RPMTorque=( 25000.0, -193.0, 848.4)
RPMTorque=( 25500.0, -193.0, 848.4)
RPMTorque=( 26000.0, -193.0, 848.4)
RPMTorque=( 26500.0, -193.0, 848.4)
RPMTorque=( 27000.0, -199.2, 854.6)
RPMTorque=( 27500.0, -199.2, 854.6)
RPMTorque=( 28000.0, -193.0, 854.6)
RPMTorque=( 28500.0, -193.0, 854.6)
RPMTorque=( 29000.0, -193.0, 865.9)
RPMTorque=( 29500.0, -193.0, 865.9)
RPMTorque=( 30000.0, -193.0, 865.9)
RPMTorque=( 30500.0, -193.0, 865.9)
RPMTorque=( 31000.0, -199.2, 865.9)
RPMTorque=( 31500.0, -211.8, 865.9)
RPMTorque=( 32000.0, -230.6, 865.9)
RPMTorque=( 32500.0, -236.8, 872.2)
RPMTorque=( 33000.0, -249.4, 872.2)
RPMTorque=( 33500.0, -255.6, 872.2)
RPMTorque=( 34000.0, -268.2, 872.2)
RPMTorque=( 34500.0, -268.2, 872.2)
RPMTorque=( 35000.0, -274.4, 872.2)
RPMTorque=( 35500.0, -274.4, 883.5)
RPMTorque=( 36000.0, -268.2, 883.5)
RPMTorque=( 36500.0, -261.9, 875.9)
RPMTorque=( 37000.0, -261.9, 883.5)
RPMTorque=( 37500.0, -261.9, 891.0)
RPMTorque=( 38000.0, -261.9, 906.0)
RPMTorque=( 38500.0, -261.9, 906.0)
RPMTorque=( 39000.0, -268.2, 906.0)
RPMTorque=( 39500.0, -249.4, 906.0)
RPMTorque=( 40000.0, -243.1, 898.5)
RPMTorque=( 40500.0, -243.1, 898.5)
RPMTorque=( 41000.0, -243.1, 898.5)
RPMTorque=( 41500.0, -243.1, 898.5)
RPMTorque=( 42000.0, -243.1, 898.5)
RPMTorque=( 42500.0, -243.1, 898.5)
RPMTorque=( 43000.0, -243.1, 898.5)
RPMTorque=( 43500.0, -243.1, 898.5)
RPMTorque=( 44000.0, -243.1, 898.5)
RPMTorque=( 44500.0, -243.1, 898.5)
RPMTorque=( 45000.0, -243.1, 898.5)
RPMTorque=( 45500.0, -243.1, 898.5)
RPMTorque=( 46000.0, -243.1, 898.5)
RPMTorque=( 46500.0, -243.1, 898.5)
RPMTorque=( 47000.0, -243.1, 898.5)
RPMTorque=( 47500.0, -243.1, 898.5)
RPMTorque=( 48000.0, -243.1, 898.5)
RPMTorque=( 48500.0, -243.1, 898.5)
RPMTorque=( 49000.0, -243.1, 898.5)
RPMTorque=( 49500.0, -243.1, 898.5)
RPMTorque=( 50000.0, -243.1, 898.5)
RPMTorque=( 50500.0, -243.1, 898.5)
RPMTorque=( 51000.0, -243.1, 898.5)
RPMTorque=( 51500.0, -243.1, 898.5)
RPMTorque=( 52000.0, -243.1, 898.5)
RPMTorque=( 52500.0, -243.1, 898.5)
FuelConsumption=4.700e-05 // affected by throttle position and engine speed
FuelEstimate=0.89300 // fudge factor for differences between vehicle types (used for lap estimates and AI pit scheduling)
EngineInertia=0.0560 // rotational inertia of engine components
IdleThrottle=0.75000 // throttle multiplier to help maintain idle speed
IdleRPMLogic=(6350, 6450) // attempt to maintain idle speed between these RPMs
RevLimitRange=(50000, 100, 1) //(10000, 0, 1)
RevLimitSetting=0
RevLimitLogic=50 // RPM range around current setting where rev limiter operates
RevLimitAvailable=0 // whether to use a rev limit (if 0, you still must have a "rev limit", just make it 40000 or so, and make sure to change [CONTROLS]->UpshiftAlgorithm to fix shifting points)
OptimumOilTemp=100.50 // degrees Celsius at which engine operates optimally
CombustionHeat=41 // degrees Celsius added per liter of fuel burned
EngineSpeedHeat=0.000e-005 // heat added linearly with engine speed
OilMinimumCooling=0.000e-005 // heat dissipated without oil/water transfer
OilWaterHeatTransfer=(0.000e-000,0.000e-000) // heat transfer from oil to water (base, w/ engine speed)
WaterMinimumCooling=0.000e-000 // base heat dissipated without velocity
RadiatorCooling=(9.800e-006, 9000e-006) // cooling rate with velocity (base, per setting)
LifetimeEngineRPM=(100250, 180) // (base engine speed for lifetime, range where lifetime is halved)
LifetimeOilTemp=(108, 2.5000) // (base oil temp for lifetime, range where lifetime is halved)
LifetimeAvg=150000 // average lifetime in seconds
LifetimeVar=5500 // lifetime random variance
EngineEmission=(0.20000, 0.6000, -2.5000) // where flames and smoke are emitted (relative to ref frame at rear axle)
EngineSound=(0.20000, 0.6000, -2.5000) // where engine sound is emitted (relative to ref frame at rear axle)
SpeedLimiter=0 // whether there is a pitlane speed limiter
OnboardStarter=1 // whether vehicle restarts when stalled
StarterTiming=(1.50, 0.0, 0.0) // average and variable cranking time, then blend with starting sound

scca1981 · 18 January 08, 02:24

52000 rpms!

Smuckers · 18 January 08, 02:25

in hdv
ClutchTorque=150000.0 // maximum torque that can be transferred through clutch
ClutchWear=0.0 // unimplemented
ClutchFriction=10.90 // friction torque of parts between clutch and transmission when in gear (automatically reduced in neutral)
ClutchEngageRate=0.7 // how quickly clutch is engaged with auto-clutch driving aid
BaulkTorque=150000.0

Smuckers · 18 January 08, 02:26

in tbc file
FRONT: // Arguments: ALL, FRONT, REAR, LEFT, RIGHT, FRONTLEFT, FRONTRIGHT, REARLEFT, REARRIGHT
DryLatLong=(10.860, 10.860) // (1.860, 1.860) Lateral/longitudinal coefficients in dry weather

REAR:
DryLatLong=(20.20, 20.10) // (1.860, 1.860)
WetLatLong=(0.990, 0.990)

Citation10 · 18 January 08, 05:25

Thanks a Lot , but I dont have a tbc file

Citation10 · 18 January 08, 05:30

MY GOD , i cant even drive the damn car now LMAO ... way too much power

16 January 08, 02:01	#2
LordRa9826 Join Date: Dec 2006 Location: Romania Age: 33	It's easy to do that.Open the .hdc file,lower the BodyDragBase for higher speeds,lower the Mass and the CGHeight for handling.

16 January 08, 02:33	#3
Citation10 Join Date: Dec 2007	Thanks for the reply , Do I need to lower them by the hundreds or just a lille here and there .

16 January 08, 03:33	#4
Smuckers Join Date: Jul 2007	// Zytek Engineering ZA1348 3,4L V8, max. Torque 442 nm // RPMTorque=( 0, -35.0, -36.0) RPMTorque=( 250, -36.3, -20.0) RPMTorque=( 500, -37.7, 119.0) RPMTorque=( 750, -38.9, 196.0) RPMTorque=( 1000, -39.2, 232.0) RPMTorque=( 1250, -39.9, 274.0) RPMTorque=( 1500, -40.4, 298.0) RPMTorque=( 1750, -41.1, 321.0) RPMTorque=( 2000, -41.9, 332.0) RPMTorque=( 2250, -42.1, 352.0) RPMTorque=( 2500, -42.8, 365.0) RPMTorque=( 2750, -43.7, 381.0) RPMTorque=( 3000, -44.6, 394.0) RPMTorque=( 3250, -45.4, 406.0) RPMTorque=( 3500, -46.7, 414.0) RPMTorque=( 3750, -47.5, 423.0) RPMTorque=( 4000, -48.3, 434.0) RPMTorque=( 4250, -49.6, 445.2) RPMTorque=( 4500, -50.9, 454.4) RPMTorque=( 4750, -52.0, 465.3) RPMTorque=( 5000, -54.1, 474.1) RPMTorque=( 5250, -55.3, 481.6) RPMTorque=( 5500, -56.6, 491.5) RPMTorque=( 5750, -58.4, 502.1) RPMTorque=( 6000, -60.5, 508.6) RPMTorque=( 6250, -62.8, 515.8) RPMTorque=( 6500, -64.7, 522.3) RPMTorque=( 6750, -67.4, 528.5) RPMTorque=( 7000, -70.2, 534.8) RPMTorque=( 7250, -73.0, 538.9) RPMTorque=( 7500, -74.2, 540.6) RPMTorque=( 7750, -76.3, 542.0) RPMTorque=( 8000, -78.2, 545.0) RPMTorque=( 8250, -80.2, 540.9) RPMTorque=( 8500, -81.4, 535.2) RPMTorque=( 8750, -83.2, 525.0) RPMTorque=( 9000, -85.0, 515.0) RPMTorque=( 9250, -86.5, 500.0) RPMTorque=( 9500, -87.9, 485.0) RPMTorque=( 9750, -89.5, 430.0) RPMTorque=( 10000, -91.7, 419.0) RPMTorque=( 10250, -93.7, 397.0) RPMTorque=( 10500, -97.0, 348.0) RPMTorque=( 10750, -100.5, -6.0) RPMTorque=( 11000, -101, -46.0) FuelConsumption=6.305e-005 // affected by throttle position and engine speed FuelEstimate=1.000 // fudge factor for differences between vehicle types (used for lap estimates and AI pit scheduling)0.997 EngineInertia=0.075 // rotational inertia of engine components IdleThrottle=1.0 // throttle multiplier to help maintain idle speed IdleRPMLogic=(1800.0, 2000.0) // attempt to maintain idle speed between these RPMs LaunchEfficiency=0.000 // efficiency (0.0-1.0) of launch control, or 0.0 if N/A LaunchRPMLogic=(6500.0, 8500.0) // holds RPM in this range before launch (used for AI even if launch control is N/A!) RevLimitRange=(8200.0, 100.0, 8) RevLimitSetting=3 RevLimitLogic=150.0 // RPM range around current setting where rev limiter operates RevLimitAvailable=1 // whether to use a rev limit (if 0, you still must have a "rev limit", just make it 40000 or so, and make sure to change [CONTROLS]->UpshiftAlgorithm to fix shifting points) EngineMapRange=(0, 1, 5) // 0 = most driveable, max = most power (low gears only) (unimplemented) EngineMapSetting=1 EngineBrakingMapRange=(0.0, 0.000155, 5) // input throttle is ranged from minimum to 100%, with the minimum = setting * step * RPM, EngineBrakingMapSetting=2 // the default is 1 * 0.000133 * 15000 RPM = 2% applied throttle at zero input throttle OptimumOilTemp=105.0 // degrees Celsius at which engine operates optimally CombustionHeat=30.0 // degrees Celsius added per liter of fuel burned EngineSpeedHeat=7.800e-004 // heat added linearly with engine speed OilMinimumCooling=9.150e-004 // heat dissipated without radiator OilWaterHeatTransfer=(5.550e-003,9.050e-005) // heat transfer from oil to water (base, w/ engine speed) WaterMinimumCooling=3.650e-003 // heat dissipated without radiator 3.900e-003 RadiatorCooling=(2.95e-004, 1.065e-004) // cooling rate with velocity (base, per setting)(3.00e-004, 1.060e-004) LifetimeEngineRPM=(8850.0,360.0) // (base engine speed for lifetime, range where lifetime is halved) LifetimeOilTemp=(130.0,2.90) // (base oil temp for lifetime, range where lifetime is halved) LifetimeAvg=15850 // average lifetime in seconds LifetimeVar=3800 // lifetime random variance EngineEmission=(0.0, 0.50, 0.0) // where flames and smoke are emitted (relative to ref frame at rear axle) EngineSound=(0.0, 0.50, 0.0) // where engine sound is played (relative to ref frame at rear axle) SpeedLimiter=1 // whether vehicle has a pitlane speed limiter OnboardStarter=1 // whether vehicle restarts when stalled StarterTiming=(1.4, 0.4, 1.9) // average and variable cranking time, then time to blend with starting sound

17 January 08, 00:39	#5
Citation10 Join Date: Dec 2007	I made some changed to the HDC file and I cant even drive the car now , its out of control ... would anyone mind tweaking it for me ?

18 January 08, 02:23	#8
Smuckers Join Date: Jul 2007	RPMTorque=( 0.0, -32.3, -32.3) RPMTorque=( 500.0, -32.1, -20.0) RPMTorque=( 1000.0, -33.4, 3.0) RPMTorque=( 1500.0, -35.2, 29.8) RPMTorque=( 2000.0, -37.2, 59.5) RPMTorque=( 2500.0, -39.1, 84.3) RPMTorque=( 3000.0, -40.9, 137.2) RPMTorque=( 3500.0, -42.8, 144.1) RPMTorque=( 4000.0, -44.7, 157.9) RPMTorque=( 4500.0, -46.6, 199.2) RPMTorque=( 5000.0, -48.6, 240.6) RPMTorque=( 5500.0, -50.7, 268.2) RPMTorque=( 6000.0, -52.8, 309.5) RPMTorque=( 6500.0, -55.0, 364.3) RPMTorque=( 7000.0, -57.2, 385.3) RPMTorque=( 7500.0, -59.4, 412.9) RPMTorque=( 8000.0, -61.7, 433.6) RPMTorque=( 8500.0, -63.9, 474.9) RPMTorque=( 9000.0, -66.2, 509.4) RPMTorque=( 9500.0, -68.5, 537.0) RPMTorque=( 10000.0, -70.9, 557.6) RPMTorque=( 10500.0, -73.4, 571.4) RPMTorque=( 11000.0, -76.0, 599.0) RPMTorque=( 11500.0, -78.9, 619.7) RPMTorque=( 12000.0, -82.0, 633.5) RPMTorque=( 12500.0, -85.4, 654.1) RPMTorque=( 13000.0, -89.3, 681.7) RPMTorque=( 13500.0, -93.6, 695.5) RPMTorque=( 14000.0, -98.3, 702.4) RPMTorque=( 14500.0, -103.4, 723.1) RPMTorque=( 15000.0, -109.1, 736.8) RPMTorque=( 15500.0, -114.9, 757.5) RPMTorque=( 16000.0, -120.9, 764.4) RPMTorque=( 16500.0, -127.0, 778.2) RPMTorque=( 17000.0, -133.3, 785.1) RPMTorque=( 17500.0, -139.6, 805.8) RPMTorque=( 18000.0, -146.0, 819.5) RPMTorque=( 18500.0, -155.4, 826.4) RPMTorque=( 19000.0, -155.4, 833.3) RPMTorque=( 19500.0, -161.7, 826.4) RPMTorque=( 20000.0, -174.2, 840.2) RPMTorque=( 20500.0, -180.5, 840.2) RPMTorque=( 21000.0, -193.0, 847.1) RPMTorque=( 21500.0, -193.0, 835.8) RPMTorque=( 22000.0, -193.0, 835.8) RPMTorque=( 22500.0, -193.0, 835.8) RPMTorque=( 23000.0, -193.0, 835.8) RPMTorque=( 23500.0, -193.0, 835.8) RPMTorque=( 24000.0, -193.0, 835.8) RPMTorque=( 24500.0, -193.0, 848.4) RPMTorque=( 25000.0, -193.0, 848.4) RPMTorque=( 25500.0, -193.0, 848.4) RPMTorque=( 26000.0, -193.0, 848.4) RPMTorque=( 26500.0, -193.0, 848.4) RPMTorque=( 27000.0, -199.2, 854.6) RPMTorque=( 27500.0, -199.2, 854.6) RPMTorque=( 28000.0, -193.0, 854.6) RPMTorque=( 28500.0, -193.0, 854.6) RPMTorque=( 29000.0, -193.0, 865.9) RPMTorque=( 29500.0, -193.0, 865.9) RPMTorque=( 30000.0, -193.0, 865.9) RPMTorque=( 30500.0, -193.0, 865.9) RPMTorque=( 31000.0, -199.2, 865.9) RPMTorque=( 31500.0, -211.8, 865.9) RPMTorque=( 32000.0, -230.6, 865.9) RPMTorque=( 32500.0, -236.8, 872.2) RPMTorque=( 33000.0, -249.4, 872.2) RPMTorque=( 33500.0, -255.6, 872.2) RPMTorque=( 34000.0, -268.2, 872.2) RPMTorque=( 34500.0, -268.2, 872.2) RPMTorque=( 35000.0, -274.4, 872.2) RPMTorque=( 35500.0, -274.4, 883.5) RPMTorque=( 36000.0, -268.2, 883.5) RPMTorque=( 36500.0, -261.9, 875.9) RPMTorque=( 37000.0, -261.9, 883.5) RPMTorque=( 37500.0, -261.9, 891.0) RPMTorque=( 38000.0, -261.9, 906.0) RPMTorque=( 38500.0, -261.9, 906.0) RPMTorque=( 39000.0, -268.2, 906.0) RPMTorque=( 39500.0, -249.4, 906.0) RPMTorque=( 40000.0, -243.1, 898.5) RPMTorque=( 40500.0, -243.1, 898.5) RPMTorque=( 41000.0, -243.1, 898.5) RPMTorque=( 41500.0, -243.1, 898.5) RPMTorque=( 42000.0, -243.1, 898.5) RPMTorque=( 42500.0, -243.1, 898.5) RPMTorque=( 43000.0, -243.1, 898.5) RPMTorque=( 43500.0, -243.1, 898.5) RPMTorque=( 44000.0, -243.1, 898.5) RPMTorque=( 44500.0, -243.1, 898.5) RPMTorque=( 45000.0, -243.1, 898.5) RPMTorque=( 45500.0, -243.1, 898.5) RPMTorque=( 46000.0, -243.1, 898.5) RPMTorque=( 46500.0, -243.1, 898.5) RPMTorque=( 47000.0, -243.1, 898.5) RPMTorque=( 47500.0, -243.1, 898.5) RPMTorque=( 48000.0, -243.1, 898.5) RPMTorque=( 48500.0, -243.1, 898.5) RPMTorque=( 49000.0, -243.1, 898.5) RPMTorque=( 49500.0, -243.1, 898.5) RPMTorque=( 50000.0, -243.1, 898.5) RPMTorque=( 50500.0, -243.1, 898.5) RPMTorque=( 51000.0, -243.1, 898.5) RPMTorque=( 51500.0, -243.1, 898.5) RPMTorque=( 52000.0, -243.1, 898.5) RPMTorque=( 52500.0, -243.1, 898.5) FuelConsumption=4.700e-05 // affected by throttle position and engine speed FuelEstimate=0.89300 // fudge factor for differences between vehicle types (used for lap estimates and AI pit scheduling) EngineInertia=0.0560 // rotational inertia of engine components IdleThrottle=0.75000 // throttle multiplier to help maintain idle speed IdleRPMLogic=(6350, 6450) // attempt to maintain idle speed between these RPMs RevLimitRange=(50000, 100, 1) //(10000, 0, 1) RevLimitSetting=0 RevLimitLogic=50 // RPM range around current setting where rev limiter operates RevLimitAvailable=0 // whether to use a rev limit (if 0, you still must have a "rev limit", just make it 40000 or so, and make sure to change [CONTROLS]->UpshiftAlgorithm to fix shifting points) OptimumOilTemp=100.50 // degrees Celsius at which engine operates optimally CombustionHeat=41 // degrees Celsius added per liter of fuel burned EngineSpeedHeat=0.000e-005 // heat added linearly with engine speed OilMinimumCooling=0.000e-005 // heat dissipated without oil/water transfer OilWaterHeatTransfer=(0.000e-000,0.000e-000) // heat transfer from oil to water (base, w/ engine speed) WaterMinimumCooling=0.000e-000 // base heat dissipated without velocity RadiatorCooling=(9.800e-006, 9000e-006) // cooling rate with velocity (base, per setting) LifetimeEngineRPM=(100250, 180) // (base engine speed for lifetime, range where lifetime is halved) LifetimeOilTemp=(108, 2.5000) // (base oil temp for lifetime, range where lifetime is halved) LifetimeAvg=150000 // average lifetime in seconds LifetimeVar=5500 // lifetime random variance EngineEmission=(0.20000, 0.6000, -2.5000) // where flames and smoke are emitted (relative to ref frame at rear axle) EngineSound=(0.20000, 0.6000, -2.5000) // where engine sound is emitted (relative to ref frame at rear axle) SpeedLimiter=0 // whether there is a pitlane speed limiter OnboardStarter=1 // whether vehicle restarts when stalled StarterTiming=(1.50, 0.0, 0.0) // average and variable cranking time, then blend with starting sound

18 January 08, 02:24	#9
scca1981 Join Date: Dec 2006 Age: 32	52000 rpms!

18 January 08, 02:25	#10
Smuckers Join Date: Jul 2007	in hdv ClutchTorque=150000.0 // maximum torque that can be transferred through clutch ClutchWear=0.0 // unimplemented ClutchFriction=10.90 // friction torque of parts between clutch and transmission when in gear (automatically reduced in neutral) ClutchEngageRate=0.7 // how quickly clutch is engaged with auto-clutch driving aid BaulkTorque=150000.0

18 January 08, 02:26	#11
Smuckers Join Date: Jul 2007	in tbc file FRONT: // Arguments: ALL, FRONT, REAR, LEFT, RIGHT, FRONTLEFT, FRONTRIGHT, REARLEFT, REARRIGHT DryLatLong=(10.860, 10.860) // (1.860, 1.860) Lateral/longitudinal coefficients in dry weather REAR: DryLatLong=(20.20, 20.10) // (1.860, 1.860) WetLatLong=(0.990, 0.990)

18 January 08, 05:25	#12
Citation10 Join Date: Dec 2007	Thanks a Lot , but I dont have a tbc file

18 January 08, 05:30	#13
Citation10 Join Date: Dec 2007	MY GOD , i cant even drive the damn car now LMAO ... way too much power